|
|
Plastic covers for the motors?
|
grozmaistor
|
1
|
2311
|
July 30, 2020, 04:27:20
by tombkk
|
|
|
Bootloader issue when burning it via Arduino Mega2560
|
grozmaistor
|
6
|
2772
|
May 01, 2018, 17:50:42
by grozmaistor
|
|
|
Arduino Mega 2560 and Pololu DRV8834
|
Grzesiek
|
0
|
1919
|
October 18, 2019, 17:43:11
by Grzesiek
|
|
|
hex upload error to NEW atmega162 IC
|
guitar79
|
5
|
3326
|
April 30, 2018, 16:07:58
by grozmaistor
|
|
|
Add an remote control to astroEQ
|
Hatsu
|
1
|
3212
|
September 30, 2015, 18:13:19
by TCWORLD
|
|
|
Wire thickness
|
igorb
|
1
|
2229
|
February 05, 2016, 14:45:24
by TCWORLD
|
|
|
Increasing motor speeds with Mega 2560
|
ijdarroch
|
10
|
2429
|
June 07, 2020, 10:12:49
by paul_astrix
|
|
|
2v too low for step motor voltage?
|
jmaurin
|
1
|
2447
|
February 22, 2016, 15:43:17
by TCWORLD
|
|
|
AstroEQ Hardware and Software Choices
|
johneta
|
0
|
2384
|
October 02, 2019, 07:29:06
by johneta
|
|
|
Cannot Update Controller!
|
johnyjf
|
9
|
2600
|
December 12, 2019, 12:28:52
by TCWORLD
|
|
|
"Write Failed connec tion unavailable"
|
johnyjf
|
0
|
1182
|
May 22, 2020, 15:40:34
by johnyjf
|
|
|
Loss of Com Port (Connection Timeout, Port not Available)
|
Jonesdee
|
14
|
7231
|
November 05, 2017, 12:30:40
by Jonesdee
|
|
|
Telescope slewing wrong direction
|
jtc125
|
3
|
2745
|
May 09, 2018, 06:26:16
by jtc125
|
|
|
Stepper motors do not operate - locked and get hot
|
jtc125
|
2
|
1974
|
April 28, 2018, 03:09:03
by jtc125
|
|
|
AstroEq 35V and TCM 2208 Driver
|
Julianus
|
7
|
2075
|
January 21, 2020, 18:13:12
by ecc2000
|
|
|
cant config 8.05 firmware gt2560
|
kaito83
|
6
|
3382
|
November 18, 2017, 13:20:21
by Phill
|
|
|
Change code to support LV8729 1/64 microstepping for mega2560
|
kaito83
|
2
|
1429
|
May 23, 2023, 07:58:32
by kaito83
|
|
|
Cannot controll motors
|
kaito83
|
1
|
2017
|
September 05, 2016, 05:57:15
by kaito83
|
|
|
Sidereal Stops when slew - mega2560
|
kaito83
|
0
|
1629
|
May 19, 2017, 08:01:27
by kaito83
|
|
|
K150 programmer
|
kaito83
|
2
|
2459
|
August 16, 2016, 08:16:09
by kaito83
|