|
|
wrong angle
|
dragonlost
|
2
|
2208
|
August 17, 2016, 10:52:59
by dragonlost
|
|
|
CGE need confirmation of settings.
|
telfish
|
1
|
2222
|
January 07, 2019, 09:03:54
by TCWORLD
|
|
|
Wire thickness
|
igorb
|
1
|
2226
|
February 05, 2016, 14:45:24
by TCWORLD
|
|
|
Plastic covers for the motors?
|
grozmaistor
|
1
|
2300
|
July 30, 2020, 04:27:20
by tombkk
|
|
|
Using TMC2130 with Astro EQ
|
telfish
|
1
|
2305
|
August 12, 2019, 09:19:56
by bmitchell82
|
|
|
New build Software?
|
Redshift
|
8
|
2308
|
March 11, 2023, 09:23:33
by Redshift
|
|
|
drv8825 is need the nf100 capacitor?
|
kaito83
|
1
|
2318
|
September 24, 2016, 13:21:03
by TCWORLD
|
|
|
arduino mega build with tb6600 stepper driver
|
diorip
|
2
|
2361
|
November 30, 2017, 16:53:03
by diorip
|
|
|
Changing the driver board.
|
Steelfixer
|
2
|
2367
|
August 21, 2018, 21:58:28
by Steelfixer
|
|
|
AstroEQ Hardware and Software Choices
|
johneta
|
0
|
2371
|
October 02, 2019, 07:29:06
by johneta
|
|
|
8.05 firmware gt2560 Speed/Coordinates doesnt match
|
kaito83
|
4
|
2388
|
August 16, 2017, 09:24:53
by kaito83
|
|
|
Increasing motor speeds with Mega 2560
|
ijdarroch
|
10
|
2399
|
June 07, 2020, 10:12:49
by paul_astrix
|
|
|
Getting there, two issues need solving
|
telfish
|
3
|
2412
|
January 14, 2018, 19:51:26
by telfish
|
|
|
Two sets of pulleys available
|
PhilCrompton
|
0
|
2413
|
February 26, 2016, 21:16:57
by PhilCrompton
|
|
|
2v too low for step motor voltage?
|
jmaurin
|
1
|
2432
|
February 22, 2016, 15:43:17
by TCWORLD
|
|
|
K150 programmer
|
kaito83
|
2
|
2447
|
August 16, 2016, 08:16:09
by kaito83
|
|
|
Arduino Mega - Audio Jack on PWM
|
rvaneynd
|
2
|
2476
|
October 21, 2017, 20:46:14
by rvaneynd
|
|
|
GPIO Pin Header
|
Sukramb
|
1
|
2498
|
January 16, 2016, 15:29:28
by TCWORLD
|
|
|
Stepper disabled when motion is not required
|
GigiG
|
3
|
2561
|
December 07, 2016, 13:07:19
by TCWORLD
|
|
|
Motor driver DIY non-Arduino AstroEQ
|
arunasmazeika
|
2
|
2576
|
October 12, 2016, 19:26:01
by arunasmazeika
|