Topic: hex upload error to NEW atmega162 IC (Read 3331 times)

guitar79 · « **on:** November 07, 2017, 11:46:20 »

Dear!!

I bought a astroEQ (V4.6).
It is great item for telescope controller.

I'm trying to make my own DIY astroeq.

I put my new IC(atmega162) into your astroEQ PCB and tried to firmware update but failed.

the error message is followings

------------------------------------------------------------------------
Starting AstroEQ Config Utility, V3.8.0(beta)
Time is 20:27:4
OS: Windows 10. JRE Version: 1.8.0_151. JRE Arch: x86
Creating Window. Setting DPI Scaling to 1
Setting Window Size to: 510 x 520
Setting Frame Rate
Creating Executioner thread
Connecting to Clipboard
Current Dir: C:\Users\user\Desktop\astroeq_beta\
Temp Dir: C:\__temp__AstroEQUploader\
Copying AVRDude.conf to Temp Dir.
Loading ControlP5
ControlP5 2.2.6 infos, comments, questions at http://www.sojamo.de/libraries/controlP5
Building GUI
x=0, y=104, width=510, height=352
buildBeginScreen --- ID is: begin
buildVersionCheckScreen --- ID is: versionCheck
buildFirmwareFetchScreen --- ID is: firmwareFetch
buildEEPROMWriterScreen --- ID is: EEPROMWriter
buildCheckEEPROMScreen --- ID is: checkEEPROM
buildRecoverEEPROMScreen --- ID is: recoverEEPROM
buildEnterConfigScreen --- ID is: enterConfig
buildProgramConfigScreen --- ID is: programConfig
buildDownloadFirmwareScreen --- ID is: downloadFirmware
buildTestFirmwareScreen --- ID is: testFirmware
buildFinishedScreen --- ID is: finished
Board Version: AstroEQV4-DIYBoard(includingKits)
Matched to firmware file: AstroEQV4-DIYBoard(includingKits).hex
Initialising Serial Ports
COM1 COM3
Matched to firmware file: AstroEQV4-DIYBoard(includingKits).hex
COM Port: COM3
AstroEQV4-DIYBoard(includingKits)
"C:\Users\user\Desktop\astroeq_beta\bin\avrdude" -C"C:\__temp__AstroEQUploader\avrdude.conf" -v -v -v -patmega162 -carduino -b57600 -D -P\\.\COM3 -Uflash:w:C:\__temp__AstroEQUploader\AstroEQV4-DIYBoard(includingKits).hex:i
avrdude: Version 6.0.1, compiled on Sep 18 2013 at 08:20:41
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

System wide configuration file is "C:\__temp__AstroEQUploader\avrdude.conf"

Using Port : \\.\COM3
Using Programmer : arduino
Overriding Baud Rate : 57600
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

avrdude done. Thank you.

Exit code : 1
running = false
complete = true
error = true
Upload Failed!!
---------------------------------------------------------------------------------------

I can't figure it out.

Please help me .

Park.

TCWORLD · « **Reply #1 on:** November 07, 2017, 13:30:09 »

Did you buy a pre-programmed IC from me, or is it a blank IC you bought from an electronics distributer?

guitar79 · « **Reply #2 on:** November 07, 2017, 13:43:23 »

I bought your astroEQ, and It works.

And I'm making astroEQ DIY version also.

I insert New IC from part company into your astroEQ procuct and then tried to update the firmware.

Please let me know how to make programmed IC.
Now I'm trying to make boot loader.

https://forum.arduino.cc/index.php?topic=104693.0

The message is followings.

----------------------------------------------------------------------------------------------------------
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega162 -cstk500 -PCOM4 -e -Ulock:w:0x3F:m -Uefuse:w:0xFB:m -Uhfuse:w:0xD8:m -Ulfuse:w:0xFF:m

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM4
Using Programmer : stk500
AVR Part : ATmega162
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
flash 65 10 128 0 yes 16384 128 128 4500 4500 0xff 0xff
eeprom 65 20 4 0 no 512 4 0 9000 9000 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
lock 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00

Programmer Type : STK500V2
Description : Atmel STK500
Programmer Model: STK500
Hardware Version: 1
Firmware Version Master : 2.10
Topcard : Unknown
Vtarget : 0.0 V
SCK period : 8.7 us
Varef : 0.0 V
Oscillator : Off

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e9404 (probably m162)
avrdude: erasing chip
avrdude: reading input file "0x3F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3F:
avrdude: load data lock data from input file 0x3F:
avrdude: input file 0x3F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% -0.00s

avrdude: verifying ...
avrdude: WARNING: invalid value for unused bits in fuse "lock", should be set to 1 according to datasheet
This behaviour is deprecated and will result in an error in future version
You probably want to use 0xff instead of 0x3f (double check with your datasheet first).
avrdude: 1 bytes of lock verified
avrdude: reading input file "0xFB"
avrdude: writing efuse (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0xFB:
avrdude: load data efuse data from input file 0xFB:
avrdude: input file 0xFB contains 1 bytes
avrdude: reading on-chip efuse data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of efuse verified
avrdude: reading input file "0xD8"
avrdude: writing hfuse (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xD8:
avrdude: load data hfuse data from input file 0xD8:
avrdude: input file 0xD8 contains 1 bytes
avrdude: reading on-chip hfuse data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of hfuse verified
avrdude: reading input file "0xFF"
avrdude: writing lfuse (1 bytes):

Writing | ################################################## | 100% 0.02s

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xFF:
avrdude: load data lfuse data from input file 0xFF:
avrdude: input file 0xFF contains 1 bytes
avrdude: reading on-chip lfuse data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of lfuse verified

avrdude done. Thank you.

C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega162 -cstk500 -PCOM4 -Uflash:w:C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:i -Ulock:w:0x0F:m

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM4
Using Programmer : stk500
AVR Part : ATmega162
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
flash 65 10 128 0 yes 16384 128 128 4500 4500 0xff 0xff
eeprom 65 20 4 0 no 512 4 0 9000 9000 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
lock 0 0 0 0 no 1 0 0 16000 16000 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00

Programmer Type : STK500V2
Description : Atmel STK500
Programmer Model: STK500
Hardware Version: 1
Firmware Version Master : 2.10
Topcard : Unknown
Vtarget : 0.0 V
SCK period : 8.7 us
Varef : 0.0 V
Oscillator : Off

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.03s

avrdude: Device signature = 0x1e9404 (probably m162)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex"
avrdude: writing flash (16384 bytes):

Writing | ################################################## | 100% 0.00s

avrdude: 16384 bytes of flash written
avrdude: verifying flash memory against C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:
avrdude: load data flash data from input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:
avrdude: input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex contains 16384 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 16384 bytes of flash verified
avrdude: reading input file "0x0F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x0F:
avrdude: load data lock data from input file 0x0F:
avrdude: input file 0x0F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: WARNING: invalid value for unused bits in fuse "lock", should be set to 1 according to datasheet
This behaviour is deprecated and will result in an error in future version
You probably want to use 0xcf instead of 0x0f (double check with your datasheet first).
avrdude: 1 bytes of lock verified

avrdude done. Thank you.
----------------------------------------------------------------------------------------------------------------

Thank you for your reply.

TCWORLD · « **Reply #3 on:** November 07, 2017, 13:47:21 »

As you have a blank IC, you'll need to write a the AstroEQ bootloader to it before you can program using the configuration utility..

The bootloader can be found here, along with some additional instructions: https://github.com/TCWORLD/AstroEQ/tree/master/AstroEQ-Bootloader

To program the IC you'll need either an AVR programmer, or an Arduino board set up for ArduinoISP.

guitar79 · « **Reply #4 on:** November 09, 2017, 06:23:24 »

Thank you so much...
It is fixed....

The astroEQ is working now.....

Thanks again..

grozmaistor · « **Reply #5 on:** April 30, 2018, 16:07:58 »

Hello can you describe how you burned the boot loader on the chip?
Have you used Arduino and what programmer.
I have issues with the boot loader putting it on the chip.
The Arduino IDE completes with success , but when connecting the AstroEQ via USB to the computer it is not detected and nothing happens.

Regards
Grozdan

AstroEQ Discussion Board

Author Topic: hex upload error to NEW atmega162 IC (Read 3331 times)

guitar79

hex upload error to NEW atmega162 IC

TCWORLD

Re: hex upload error to NEW atmega162 IC

guitar79

Re: hex upload error to NEW atmega162 IC

TCWORLD

Re: hex upload error to NEW atmega162 IC

guitar79

Re: hex upload error to NEW atmega162 IC

grozmaistor

Re: hex upload error to NEW atmega162 IC