Welcome, Guest. Please login or register.

Username: Password:

Author Topic: hex upload error to NEW atmega162 IC  (Read 3235 times)

guitar79

  • Newbie
  • *
  • Posts: 4
    • View Profile
hex upload error to NEW atmega162 IC
« on: November 07, 2017, 11:46:20 »

Dear!!

I bought a astroEQ (V4.6).
It is great item for telescope controller.

I'm trying to make my own DIY astroeq.

I put my new IC(atmega162) into your astroEQ PCB and tried to firmware update but failed.

the error message is followings

------------------------------------------------------------------------
Starting AstroEQ Config Utility, V3.8.0(beta)
Time is 20:27:4
OS: Windows 10. JRE Version: 1.8.0_151. JRE Arch: x86
Creating Window. Setting DPI Scaling to 1
Setting Window Size to: 510 x 520
Setting Frame Rate
Creating Executioner thread
Connecting to Clipboard
Current Dir: C:\Users\user\Desktop\astroeq_beta\
Temp Dir: C:\__temp__AstroEQUploader\
Copying AVRDude.conf to Temp Dir.
Loading ControlP5
ControlP5 2.2.6 infos, comments, questions at http://www.sojamo.de/libraries/controlP5
Building GUI
x=0, y=104, width=510, height=352
buildBeginScreen --- ID is: begin
buildVersionCheckScreen --- ID is: versionCheck
buildFirmwareFetchScreen --- ID is: firmwareFetch
buildEEPROMWriterScreen --- ID is: EEPROMWriter
buildCheckEEPROMScreen --- ID is: checkEEPROM
buildRecoverEEPROMScreen --- ID is: recoverEEPROM
buildEnterConfigScreen --- ID is: enterConfig
buildProgramConfigScreen --- ID is: programConfig
buildDownloadFirmwareScreen --- ID is: downloadFirmware
buildTestFirmwareScreen --- ID is: testFirmware
buildFinishedScreen --- ID is: finished
Board Version: AstroEQV4-DIYBoard(includingKits)
Matched to firmware file: AstroEQV4-DIYBoard(includingKits).hex
Initialising Serial Ports
COM1 COM3
Matched to firmware file: AstroEQV4-DIYBoard(includingKits).hex
COM Port: COM3
AstroEQV4-DIYBoard(includingKits)
"C:\Users\user\Desktop\astroeq_beta\bin\avrdude" -C"C:\__temp__AstroEQUploader\avrdude.conf" -v -v -v -patmega162 -carduino -b57600 -D -P\\.\COM3 -Uflash:w:C:\__temp__AstroEQUploader\AstroEQV4-DIYBoard(includingKits).hex:i
avrdude: Version 6.0.1, compiled on Sep 18 2013 at 08:20:41
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\__temp__AstroEQUploader\avrdude.conf"

         Using Port                    : \\.\COM3
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

avrdude done.  Thank you.

Exit code : 1
running = false
complete = true
error = true
Upload Failed!!
---------------------------------------------------------------------------------------

I can't figure it out.

Please help me .

Park.
Logged

TCWORLD

  • Administrator
  • *****
  • Posts: 809
    • View Profile
    • AstroEQ
Re: hex upload error to NEW atmega162 IC
« Reply #1 on: November 07, 2017, 13:30:09 »

Did you buy a pre-programmed IC from me, or is it a blank IC you bought from an electronics distributer?
Logged
Tom Carpenter (AstroEQ)

guitar79

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: hex upload error to NEW atmega162 IC
« Reply #2 on: November 07, 2017, 13:43:23 »

I bought your astroEQ, and It works.

And I'm making astroEQ DIY version also.

I insert New IC from part company into your astroEQ procuct and then tried to update the firmware.

Please let me know how to make programmed IC.
Now I'm trying to make boot loader.

https://forum.arduino.cc/index.php?topic=104693.0

The message is followings.

----------------------------------------------------------------------------------------------------------
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega162 -cstk500 -PCOM4 -e -Ulock:w:0x3F:m -Uefuse:w:0xFB:m -Uhfuse:w:0xD8:m -Ulfuse:w:0xFF:m

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM4
         Using Programmer              : stk500
         AVR Part                      : ATmega162
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           flash         65    10   128    0 yes     16384  128    128  4500  4500 0xff 0xff
           eeprom        65    20     4    0 no        512    4      0  9000  9000 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           lock           0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00

         Programmer Type : STK500V2
         Description     : Atmel STK500
         Programmer Model: STK500
         Hardware Version: 1
         Firmware Version Master : 2.10
         Topcard         : Unknown
         Vtarget         : 0.0 V
         SCK period      : 8.7 us
         Varef           : 0.0 V
         Oscillator      : Off

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e9404 (probably m162)
avrdude: erasing chip
avrdude: reading input file "0x3F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3F:
avrdude: load data lock data from input file 0x3F:
avrdude: input file 0x3F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% -0.00s

avrdude: verifying ...
avrdude: WARNING: invalid value for unused bits in fuse "lock", should be set to 1 according to datasheet
This behaviour is deprecated and will result in an error in future version
You probably want to use 0xff instead of 0x3f (double check with your datasheet first).
avrdude: 1 bytes of lock verified
avrdude: reading input file "0xFB"
avrdude: writing efuse (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0xFB:
avrdude: load data efuse data from input file 0xFB:
avrdude: input file 0xFB contains 1 bytes
avrdude: reading on-chip efuse data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 1 bytes of efuse verified
avrdude: reading input file "0xD8"
avrdude: writing hfuse (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xD8:
avrdude: load data hfuse data from input file 0xD8:
avrdude: input file 0xD8 contains 1 bytes
avrdude: reading on-chip hfuse data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of hfuse verified
avrdude: reading input file "0xFF"
avrdude: writing lfuse (1 bytes):

Writing | ################################################## | 100% 0.02s

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xFF:
avrdude: load data lfuse data from input file 0xFF:
avrdude: input file 0xFF contains 1 bytes
avrdude: reading on-chip lfuse data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: 1 bytes of lfuse verified

avrdude done.  Thank you.

C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega162 -cstk500 -PCOM4 -Uflash:w:C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:i -Ulock:w:0x0F:m

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM4
         Using Programmer              : stk500
         AVR Part                      : ATmega162
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           flash         65    10   128    0 yes     16384  128    128  4500  4500 0xff 0xff
           eeprom        65    20     4    0 no        512    4      0  9000  9000 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           lock           0     0     0    0 no          1    0      0 16000 16000 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00

         Programmer Type : STK500V2
         Description     : Atmel STK500
         Programmer Model: STK500
         Hardware Version: 1
         Firmware Version Master : 2.10
         Topcard         : Unknown
         Vtarget         : 0.0 V
         SCK period      : 8.7 us
         Varef           : 0.0 V
         Oscillator      : Off

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.03s

avrdude: Device signature = 0x1e9404 (probably m162)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
         To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex"
avrdude: writing flash (16384 bytes):

Writing | ################################################## | 100% 0.00s

avrdude: 16384 bytes of flash written
avrdude: verifying flash memory against C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:
avrdude: load data flash data from input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex:
avrdude: input file C:\Program Files (x86)\Arduino\hardware\arduino\avr/bootloaders/optiboot_atmega162.hex contains 16384 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.00s

avrdude: verifying ...
avrdude: 16384 bytes of flash verified
avrdude: reading input file "0x0F"
avrdude: writing lock (1 bytes):

Writing | ################################################## | 100% 0.03s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x0F:
avrdude: load data lock data from input file 0x0F:
avrdude: input file 0x0F contains 1 bytes
avrdude: reading on-chip lock data:

Reading | ################################################## | 100% 0.01s

avrdude: verifying ...
avrdude: WARNING: invalid value for unused bits in fuse "lock", should be set to 1 according to datasheet
This behaviour is deprecated and will result in an error in future version
You probably want to use 0xcf instead of 0x0f (double check with your datasheet first).
avrdude: 1 bytes of lock verified

avrdude done.  Thank you.
----------------------------------------------------------------------------------------------------------------

Thank you for your reply.


« Last Edit: November 07, 2017, 13:46:32 by guitar79 »
Logged

TCWORLD

  • Administrator
  • *****
  • Posts: 809
    • View Profile
    • AstroEQ
Re: hex upload error to NEW atmega162 IC
« Reply #3 on: November 07, 2017, 13:47:21 »

As you have a blank IC, you'll need to write a the AstroEQ bootloader to it before you can program using the configuration utility..

The bootloader can be found here, along with some additional instructions: https://github.com/TCWORLD/AstroEQ/tree/master/AstroEQ-Bootloader

To program the IC you'll need either an AVR programmer, or an Arduino board set up for ArduinoISP.
Logged
Tom Carpenter (AstroEQ)

guitar79

  • Newbie
  • *
  • Posts: 4
    • View Profile
Re: hex upload error to NEW atmega162 IC
« Reply #4 on: November 09, 2017, 06:23:24 »

Thank you so much...
It is fixed....

The astroEQ is working now.....

Thanks again..
Logged

grozmaistor

  • Full Member
  • ***
  • Posts: 11
    • View Profile
Re: hex upload error to NEW atmega162 IC
« Reply #5 on: April 30, 2018, 16:07:58 »

Hello can you describe how you burned the boot loader on the chip?
Have you used Arduino and what programmer.
I have issues with the boot loader putting it on the chip.
The Arduino IDE completes with success , but when connecting the AstroEQ via USB to the computer it is not detected and nothing happens.

Regards
Grozdan
Logged
Grozdan Grozev, amateur enthusiast